Kisslicer Pro - IDEX

Discuss general topics that don't suit another sub-forum

Kisslicer Pro - IDEX

Postby olo2000pm » 08 Feb 2019, 17:22

Hey.
I built IDEX type printer.
Can you share the start code?
I do not know how to make it work properly in ditto mode.
I have a duet wifi and duex
olo2000pm
 
Posts: 8
Joined: 04 Jun 2017, 15:04

Re: Kisslicer Pro - IDEX

Postby olo2000pm » 11 Feb 2019, 06:26

I have electronics duet WiFi and duex. Nobody knows how to initiate a print in ditto mode?
olo2000pm
 
Posts: 8
Joined: 04 Jun 2017, 15:04

Re: Kisslicer Pro - IDEX

Postby pjr » 11 Feb 2019, 10:26

olo2000pm wrote:Nobody knows how to initiate a print in ditto mode?


Very unlikely that is the case. However I certainly don't but I am guessing it would not be too difficult to get it set up...

Have you printed anything at all on this printer? Do you have any files already sliced? If so, you could post one here and I will take a look.

Peter
Please note: I do not have any affiliation with KISSlicer. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage or loss.
User avatar
pjr
 
Posts: 558
Joined: 05 May 2015, 10:27
Location: Kamnik, Slovenia

Re: Kisslicer Pro - IDEX

Postby olo2000pm » 12 Feb 2019, 05:37

olo2000pm
 
Posts: 8
Joined: 04 Jun 2017, 15:04

Re: Kisslicer Pro - IDEX

Postby pjr » 12 Feb 2019, 05:58

Brilliant. :D

Now you can share ;)

Peter
Please note: I do not have any affiliation with KISSlicer. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage or loss.
User avatar
pjr
 
Posts: 558
Joined: 05 May 2015, 10:27
Location: Kamnik, Slovenia

Re: Kisslicer Pro - IDEX

Postby olo2000pm » 12 Feb 2019, 13:55

I created the third head.
I open the file and click on it and choose the third head.
prefix:
; [mm] tryb
G21
G90
M82
G28
T0
M140 S <BED>
M116
M104 S <TEMP>
M116
T1
M106
T <EXT + 0>
M109 S <TEMP>
M104 S <TEMP>
T2

The rest I'm doing is the duet wifi software.
Attachments
kisslicer2.jpg
kisslicer1.jpg
kisslicer1.jpg (105.75 KiB) Viewed 1526 times
olo2000pm
 
Posts: 8
Joined: 04 Jun 2017, 15:04

Re: Kisslicer Pro - IDEX

Postby olo2000pm » 08 Mar 2019, 02:23

It does not work well. When I want to print from ABS and PVA, is T0 setting me 205'C instead of 245? I have defined heads in EXT MAP. What needs to be changed?
olo2000pm
 
Posts: 8
Joined: 04 Jun 2017, 15:04

Re: Kisslicer Pro - IDEX

Postby pjr » 08 Mar 2019, 09:16

olo2000pm wrote:It does not work well. When I want to print from ABS and PVA, is T0 setting me 205'C instead of 245? I have defined heads in EXT MAP. What needs to be changed?


Please look at Settings/Printer G-code/Select New Ext & Warm

There should be something like this:

Code: Select all
T<EXT+0>
M104 S<TEMP>


Peter
Please note: I do not have any affiliation with KISSlicer. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage or loss.
User avatar
pjr
 
Posts: 558
Joined: 05 May 2015, 10:27
Location: Kamnik, Slovenia

Re: Kisslicer Pro - IDEX

Postby Pocohanthes » 03 Jun 2019, 15:10

I tried same procedure posted here but it doesn't work. I might be doing something wrongly though.
Pocohanthes
 
Posts: 2
Joined: 24 May 2019, 06:28


Return to General

Who is online

Users browsing this forum: No registered users and 0 guests