Under extrusion on higher layer height

Under extrusion on higher layer height

Postby jussi » 19 Feb 2019, 14:46

Hello,

I'm using v2 a 0.4.4 version. I tweaked flow 0.95 to get nice top surface and no messy anywhere. But that setting somehow change with layer height. If I print max. 0.25 I get good results but higher than that under extrusion? I'm using ASA and printer is prusa mk2 with volcano hotend 0.6 nozzle. Left is with 035 settings and right ones with 025 settings. Huge difference.
Other thing I noticed is that 1st layer is almost every time something else than set.

2019-02-19 21.19.53.jpg

025settings.jpg
025settings.jpg (132.66 KiB) Viewed 287 times

035settings.jpg
035settings.jpg (134.92 KiB) Viewed 287 times
jussi
 
Posts: 3
Joined: 19 Feb 2019, 13:56
Location: Finland

Re: Under extrusion on higher layer height

Postby pjr » 19 Feb 2019, 15:50

Check out the Settings/Printer/Hardware/Loop Solid Infill Overlap (slider setting).

Needs to be around 1.7

Peter
Please note: I do not have any affiliation with KISSlicer. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage or loss.
User avatar
pjr
 
Posts: 520
Joined: 05 May 2015, 10:27
Location: Kamnik, Slovenia

Re: Under extrusion on higher layer height

Postby jussi » 19 Feb 2019, 15:54

It's 0.75, is that somehow changed from 1.6 to v2? 025 layer height it prints fine with that and there is gap between lines also
jussi
 
Posts: 3
Joined: 19 Feb 2019, 13:56
Location: Finland

Re: Under extrusion on higher layer height

Postby pjr » 19 Feb 2019, 16:11

jussi wrote:It's 0.75, is that somehow changed from 1.6 to v2? 025 layer height it prints fine with that and there is gap between lines also


The range was changed from 0 to 1 in V1.6 to 0 to 2 in V2.

Peter
Please note: I do not have any affiliation with KISSlicer. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage or loss.
User avatar
pjr
 
Posts: 520
Joined: 05 May 2015, 10:27
Location: Kamnik, Slovenia

Re: Under extrusion on higher layer height

Postby jussi » 19 Feb 2019, 16:17

ok, so v1.6 setting 0.75 is 1.5 on v2?
jussi
 
Posts: 3
Joined: 19 Feb 2019, 13:56
Location: Finland

Re: Under extrusion on higher layer height

Postby pjr » 19 Feb 2019, 17:14

jussi wrote:ok, so v1.6 setting 0.75 is 1.5 on v2?


I suppose in theory that is correct ;)

Slice a model or two, look at the paths on the top layer and have the "3D" check box ticked. You will see what you need. Don't take any notice of the first layer; that seems to work differently.

Peter
Please note: I do not have any affiliation with KISSlicer. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage or loss.
User avatar
pjr
 
Posts: 520
Joined: 05 May 2015, 10:27
Location: Kamnik, Slovenia


Return to Troubleshooting

Who is online

Users browsing this forum: Cthutq and 0 guests