CubeX PLA fans not running?

Post Reply
pingu
Posts: 5
Joined: 18 Jan 2017, 15:25

CubeX PLA fans not running?

Post by pingu »

Hi,

running Kisslicer/Cubeitmod and trying out PLA. The fans are not running so the PLA gets a bit burnt. I see the fan g-gode is checked in Kisslicer.

Any ideas appriciated!
sadclown706
Posts: 4
Joined: 04 Oct 2016, 13:35

Re: CubeX PLA fans not running?

Post by sadclown706 »

Have you verified the fans are working?
Press "PJ-CONN" the fans should turn on.
pingu
Posts: 5
Joined: 18 Jan 2017, 15:25

Re: CubeX PLA fans not running?

Post by pingu »

Good call thanks!

They do work, but there is a Code 13 error present when I try the PJ-Con. Then the fans spin. So code 13..hmm..
pingu
Posts: 5
Joined: 18 Jan 2017, 15:25

Re: CubeX PLA fans not running?

Post by pingu »

Now PJ-Con colling fans turn on, but when I print PLA - no fans. :roll:
Giovanni V.
Posts: 241
Joined: 18 Nov 2014, 09:34

Re: CubeX PLA fans not running?

Post by Giovanni V. »

pingu wrote:Now PJ-Con colling fans turn on, but when I print PLA - no fans. :roll:
How much do you have for Fan Z [mm] into Matl table ?
Under Printer / Firmware is Fan ON = M106 ?
pingu
Posts: 5
Joined: 18 Jan 2017, 15:25

Re: CubeX PLA fans not running?

Post by pingu »

Giovanni:

The mtrl settings are default. How should I change it?

Thanks.
Giovanni V.
Posts: 241
Joined: 18 Nov 2014, 09:34

Re: CubeX PLA fans not running?

Post by Giovanni V. »

Send some screen shots of your settings
pingu wrote:Giovanni:

The mtrl settings are default. How should I change it?

Thanks.
moo00se
Posts: 8
Joined: 26 Apr 2017, 01:49

Re: CubeX PLA fans not running?

Post by moo00se »

How much do you have for Fan Z [mm] into Matl table ?
The default is 200
Under Printer / Firmware is Fan ON = M106 ? Yes for me.

I have installed all of this fore the first time. I struggled with using 491 before i found this thread :lol: My first print with 6.05 the part fans did not run. The part is 12mm tall.
Attachments
Capture.PNG
Capture.PNG (28.18 KiB) Viewed 3370 times
Giovanni V.
Posts: 241
Joined: 18 Nov 2014, 09:34

Re: CubeX PLA fans not running?

Post by Giovanni V. »

moo00se wrote:How much do you have for Fan Z [mm] into Matl table ?
The default is 200
Under Printer / Firmware is Fan ON = M106 ? Yes for me.

I have installed all of this fore the first time. I struggled with using 491 before i found this thread :lol: My first print with 6.05 the part fans did not run. The part is 12mm tall.

If you set "Fan Z = 0 " the fan will start from first layer, if you set FanZ =0.4 and you have 0.2 for layer thickness the fan will not work for the first 2 layers and after the fan will be turned on.
moo00se
Posts: 8
Joined: 26 Apr 2017, 01:49

Re: CubeX PLA fans not running?

Post by moo00se »

Thanks!
Post Reply