SuperFly and some other prints...

SuperFly and some other prints...

Postby pjr » 27 Oct 2017, 03:04

IMG_20171027_094641.jpg


https://www.thingiverse.com/thing:2564723 (200%)

4C Red, Yellow, White (eyes) and Transparent (wings)

Purge: 30, 50, 50, 60; Slight bleed on the white - should have purged 60mm.

0.2mm layers with support (now removed)

14h 51m

Peter
Please note: I do not have any affiliation with KISSlicer. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage or loss.
User avatar
pjr
 
Posts: 452
Joined: 05 May 2015, 10:27
Location: Slovenia

Re: SuperFly

Postby lonesock » 27 Oct 2017, 12:10

Very nice! (I'm glad you mentioned the materials...for some reason from the pic I was thinking the eyes and wings used the same material and the color variation was due to the light.) 15 hours! Time sure flies...(sorry!)

Jonathan
User avatar
lonesock
 
Posts: 256
Joined: 09 Nov 2014, 18:41

Re: SuperFly

Postby inventabuild » 30 Oct 2017, 21:24

Nice!
inventabuild
 
Posts: 259
Joined: 09 Nov 2014, 23:03

Om Nom and a turtle

Postby pjr » 31 Oct 2017, 10:16

IMG_20171031_093836.jpg


Variable layer height, both printed together ("Joint") and a little more purging on the lighter colours.

And thanks again to Roman for the models!

Peter
Please note: I do not have any affiliation with KISSlicer. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage or loss.
User avatar
pjr
 
Posts: 452
Joined: 05 May 2015, 10:27
Location: Slovenia

Racing frogs

Postby pjr » 31 Oct 2017, 11:13

IMG_20171031_170955.jpg


0.2mm layers, 5h 13m

Peter
Please note: I do not have any affiliation with KISSlicer. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage or loss.
User avatar
pjr
 
Posts: 452
Joined: 05 May 2015, 10:27
Location: Slovenia

Articulated Fish.

Postby pjr » 07 Nov 2017, 06:40

I was reminded of this print by another forum user. It had been a while (11 months) since I printed this as a 2C model and part of the PR MMU Beta test programme.

IMG_20171107_123419.jpg


This model however was printed with variable layer heights, multiple models and sizes and 4C. Print time 11h 42m.

Peter
Please note: I do not have any affiliation with KISSlicer. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage or loss.
User avatar
pjr
 
Posts: 452
Joined: 05 May 2015, 10:27
Location: Slovenia

Useless Piggy Bank

Postby pjr » 09 Nov 2017, 08:11

Decided to try this print for my kids: https://www.thingiverse.com/thing:437576

It looked a little small, so I increased the size to 150%

IMG_20171109_140321.jpg


Now all the money can fall out... :cry:

Peter
Please note: I do not have any affiliation with KISSlicer. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage or loss.
User avatar
pjr
 
Posts: 452
Joined: 05 May 2015, 10:27
Location: Slovenia


Return to Gallery

Who is online

Users browsing this forum: No registered users and 1 guest